There are a few options if you don't feel confident installing or removing the vanity light in your bathroom. The first step is to separate the in-wall wiring from the current fixture wire. When you've done that, double-check that the cables hanging out of the wall aren't frayed or otherwise unsafe. After that, you may install the new mirror light.
Get Rid of Your Current Egotism
It's crucial to remember basic safety precautions whenever working with electricity, and that includes changing vanity bulb to something other, installing a new vanity light or swapping out an old one. Improper work practices may be avoided if everyone does their part.
Reading and following the manufacturer-supplied installation instructions is a simple method to replace the sconces and reduce the likelihood of injury. Specifics on a ground screw or a voltage tester that doesn't need touching the wires might fall into this category. Having them on hand can greatly improve the efficiency of the procedure.
Make sure the bathroom's breaker is off before you begin. You'll need electricity to operate your lights, so this is crucial. Having two or more lighting fixtures is recommended for bigger mirrors. Remember that the installed light will be visible from the attic, and take appropriate safety precautions.
Cut the Wires Connecting the Fixture to the Wall
Before installing your new vanity light, you must first remove the old fixture from the wall and cut power to it at the electrical outlet. Several people take on this type of task on their own. Nonetheless, to avoid unpleasant surprises, be sure to follow the manufacturer's instructions.
Making a diagram of your current lighting setup might be helpful as well. Maybe the light isn't turning on because of a problem with the connections between two or more of these wires.
You can get help from a professional if you don't know how to take the light fixture apart. This, though, may be a mammoth task. To avoid harm, please use caution.
Using a junction box, you may install the new light fixture. Having this metal box installed will ensure that the wiring from the fixture is connected to the wire already present in the wall. If the box has a grounding screw, it must be grounded.
Verify the Exposed Wiring in the Wall
Always double-check the exposed wires when putting in a new vanity light. You should probably check that the breaker is turned off before attempting to work on them, too. As a result, fewer people will be hurt or burned.
First, go to the electrical panel and shut off the power. You should have a buddy check the breaker for you if you are unsure of its location.
After turning off the circuit breaker, the old bulb may be taken out. A junction box on the rear of the fixture will be clearly visible. It seems like it's in a fantastic spot and will serve as an excellent reference point while you're wiring in your new lamp.
Your next step is to take the old lamp's shades off. Careful, there are several tiny screws holding the blinds in place.
Get the New Mirror Light Set Up
Putting up a vanity light for the first time might be a little nerve-wracking. If you follow the steps below, you won't need a professional electrician or handyman to put in new lights in your bathroom.
Make sure you have a fully-functioning light fixture before proceeding. An attachment plate, a backplate, a grounding wire, and a base plate are all necessary components. You'll need them in order to wire your new vanity light into your home's electrical system.
The next step is to unplug the old fixture from the wall. To do so, you need to take off the lamp's little screw cap and turn off the light. In addition, you'll need to remove 0.63 inches of insulation from the wires.
When you've stripped all the wires, you may plug the fixture into the electrical box. Connect the white and black wires using wire nuts. In most cases, the grounding screw will have a green head that the grounding wire may be wrapped around.
Keep Your Eyes Peeled for the Light Switch to Avoid Turning it Back on by Accident
In the midst of your job, it's easy to lose sight of the fact that the ground you're standing on is live wiring. This necessitates your taking certain safety precautions. The safest method is to place the lamp within a locked container. As an alternative, you might hire an expert for the job.
Time-consuming though it may be, this method guarantees success. Remember that fuses are far less forgiving than contemporary circuit breakers, so take caution if you decide to use one. Why not rewire the entire house while you're at it? Short-term effort now will provide long-term savings in both money and time.
